ECU6 chip pinout
Al Lipper
efi at cardozo.org
Thu Jun 24 17:22:27 GMT 1999
Bob, the chips are identical. Different companies use different names for
some of the pins - don't worry about the names and just hook it up the way
it is in the schematic. the 74573 is the base version of the IC, the
74HC573 is the Hight-speed CMOS version. Since the circuit uses a CMOS
CPU, you should use CMOS chips other places. I don't know that the
High-speed option matters a whole lot, but it wouldn't be a bad idea.
Remember, the ECU6 circuit has been built and tested - it works as it is.
You might need some extra filtering for your particular application, but
the digital part is pretty solid.
Al
At 07:38 PM 6/24/99 +0000, you wrote:
>
>
>
>>From: Al Lipper <efi at cardozo.org>
>>To: yip yee keong <wungun73 at hotmail.com>
>>Subject: Re: 74hc573 pin out doubt
>>Date: Wed, 23 Jun 1999 17:21:26 -0700
>> 74573
> +---\/---+
>1 -|/oe Vcc|- 20
>2 -|d0 q0|- 19
>3 -|d1 q1|- 18
>4 -|d2 q2|- 17
>5 -|d3 q3|- 16 <-----this is the pinout u show me
>6 -|d4 q4|- 15
>7 -|d5 q5|- 14
>8 -|d6 q6|- 13
>9 -|d7 q7|- 12
>10 -|gnd le|- 11
> +--------+
>
>
> +---\/---+
>1 -[oc ]- 20
>2 -[d1 q1]- 19
>3 -[d2 q2]- 18
>4 -[d3 q3]- 17
>5 -[d4 q4]- 16 <-----this is the pinout on the shecmatic drawing
>6 -[d5 q5]- 15 showing the (74hc573)
>7 -[d6 q6]- 14
>8 -[d7 q7]- 13
>9 -[d8 q8]- 12
>10 -[ c]- 11
> +--------+
>
>Is the 74573 compatible with the 74hc573 ????,on the drawing above there is
>a quite differ on the pin out did u see it any.
>
>>Bob,
>> I'm not familiiar with the Harris version of the 74HC573, but I suspect
>>you may be looking at the wrong package of the chip - I use a 20-pin DIP
>>(see: http://www.hitex.com/chipdir/pin/74573.txt for a pinout). The
>>software is loaded into the flash memory using an EPROM programmer. I hope
>>this helps.
>>
>> Al
>>
>>
>>At 01:35 AM 6/24/99 +0000, you wrote:
>> >hi,mr lipper,my name is bob,from malaysia,after looking into the diy
>>ecu,i
>> >was interested in buliding,ecu 6 for my car,on the shecmetic diagram with
>>u
>> >draw,there is the (74hc573)chip pinout that i doubt about,because when
>>i'm
>> >trying to find the specify chip in harris documant it turns out that the
>> >pinout was in different position,hope that u could help me on the specify
>> >chip,and about installation of the software to the ecu,because i'm new to
>> >logic/software transfer.thanks
>> >
>> > 74573
> +---\/---+
>1 -|/oe Vcc|- 20
>2 -|d0 q0|- 19
>3 -|d1 q1|- 18
>4 -|d2 q2|- 17
>5 -|d3 q3|- 16 <-----this is the pinout u show me
>6 -|d4 q4|- 15
>7 -|d5 q5|- 14
>8 -|d6 q6|- 13
>9 -|d7 q7|- 12
>10 -|gnd le|- 11
> +--------+
>
>
> +---\/---+
>1 -[oc ]- 20
>2 -[d1 q1]- 19
>3 -[d2 q2]- 18
>4 -[d3 q3]- 17
>5 -[d4 q4]- 16 <-----this is the pinout on the shecmatic drawing
>6 -[d5 q5]- 15 showing the (74hc573)
>7 -[d6 q6]- 14
>8 -[d7 q7]- 13
>9 -[d8 q8]- 12
>10 -[ c]- 11
> +--------+
>
>Is the 74573 compatible with the 74hc573 ????,on the drawing above there is
>a quite differ on the pin out did u see it any.
>
>> >______________________________________________________
>> >Get Your Private, Free Email at http://www.hotmail.com
>>
>
>
>______________________________________________________
>Get Your Private, Free Email at http://www.hotmail.com
More information about the Diy_efi
mailing list