Wreckers, efi parts, which ones?

[P.J.Berg]

Where did you find that info??
I have a copy of their price sheet, and cannot say I have seen the amount
you refer to??!

Cheers  J.



P.J.Berg
BergRace at Aircooled.net





----- Original Message -----
From: "Wes Branchflower" <hemi_265 at hotmail.com>
To: <diy_efi at diy-efi.org>
Sent: Sunday, January 21, 2001 9:19 PM
Subject: Re: Wreckers, efi parts, which ones?


> Hmm.. it says $850 US.. which is about $1600 Australian. I forgot to
mention
> i'm in Australia.
> I think I need to use a MAF system, because i'll be using a hot cam.
> But thanks anyway. I'll definetly keep them in mind.
>
>
>
> >From: "P.J.Berg" <BergRace at c2i.net>
> >Reply-To: diy_efi at diy-efi.org
> >To: <diy_efi at diy-efi.org>
> >Subject: Re: Wreckers, efi parts, which ones?
> >Date: Sun, 21 Jan 2001 19:08:33 +0100
> >
> >Go to www.PerfectPower.com  (South Africa)
> >The ECU is the cheapest, the MIC3 runs at 423,-U.S.$ including all
sensors
> >comunication cable at two-2 Ignition amplifiers.
> >
> >Tell them BergRace sendt you.
> >
> >
> >
> >
> >P.J.Berg
> >BergRace at Aircooled.net
> >
> >
> >
> >
> >
> >----- Original Message -----
> >From: "Wes Branchflower" <hemi_265 at hotmail.com>
> >To: <diy_efi at diy-efi.org>
> >Sent: Sunday, January 21, 2001 6:03 PM
> >Subject: Wreckers, efi parts, which ones?
> >
> >
> > > I'm making a multiport EFi setup for my 265cu (4.3L) hemi six.
> > > I've got the manifolds pretty much on their way, but, i'm just a
little
> > > stuck with the rest of it.
> > >
> > > Does anyone recommend a good EFi computer, which is easily programmed,
> >and
> > > is available relatively cheap?
> > >
> > > Also, i'm weighing up between sensors, and i'll probablty be using a
MAF
> >as
> > > i'll be using a fairly lumpy cam, which might upset a MAP sensor?
> > >
> > > I'm looking to source things from a wreckers, and wanting to keep on a
> > > budget. I already have a Ford XF 4.1 litre throttle body/TPS +
> > > injectors/fuel pressure regulator.
> > >
> > > Are the following all I need for my setup:
> > >
> > > MAF Meter
> > > Throttle Position Sensor
> > > Crank Angle sensor (or can i just do it from the coil?)
> > > Coolant Temp Sensor
> > > Fuel Pump
> > > Fuel Pressure Regulator
> > >
> > >
> > > MAF Meter - Do popular aftermarket ECU's accept both MAP or MAF
sensors.
> > >             Does it matter what 'size' a MAF is? Any suggestions for a
> > > make which I should look for? (Ford? Holden? etc?)
> > >
> > > Throttle Pos Sensor - I have the one which came with the XF Ford
> >throttle
> > > body, It doesn't seem to have any output except WOT and IDLE.
> > > Either that or it's broken.. :( Is this all i need?
> > >
> > > Do I need a crank angle sensor for plain multi-port efi? (not
> >sequential)
> > >
> > > Do i need a coolant temp sensor? are their any makes/models that I can
> >pull
> > > one from at a wreckers if so? where are they located?
> > >
> > > Fuel Pump - Will a stock ford EFi pump do? I'm using the ford
injectors
> >and
> > > pressure regulator.
> > >
> > > Any input greatly appriecated.
> > > Thanks.
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> >_________________________________________________________________________
> > > Get Your Private, Free E-mail from MSN Hotmail at
> >http://www.hotmail.com.
> > >
> > >
>
>--------------------------------------------------------------------------
> >--
> > > To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
> >quotes)
> > > in the body of a message (not the subject) to
> >majordomo at lists.diy-efi.org
> > >
> >
> >
>
>---------------------------------------------------------------------------
-
> >To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
> >quotes)
> >in the body of a message (not the subject) to majordomo at lists.diy-efi.org
> >
>
> _________________________________________________________________________
> Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
>
> --------------------------------------------------------------------------
--
> To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
quotes)
> in the body of a message (not the subject) to majordomo at lists.diy-efi.org
>


----------------------------------------------------------------------------
To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org