[Gmecm] 7747 High BLM at idle

[Programmer]

Your O2 sensor may cool down (rendering anything monitored relatively
useless) and values start to go weird.
150 means it's starting to add fuel because 'seeing lean'.

Is it really lean--how else will you know ? Are you still giving the ECM an
'in gear' signal ? Is the idle speed higher than normal ? What about the
spark curve ? Too much idle advance--exhaust temps will drop--O2's get
colder -- however it's commanded to monitor the value still-- and BLM's get
whacked.

I'd also tend to not rely on freeware so much. Just my .02

Lyndon

----- Original Message ----- 
From: <charles at taildragger.info>
To: <gmecm at diy-efi.org>
Sent: Friday, August 19, 2005 9:06 AM
Subject: Re: [Gmecm] 7747 High BLM at idle


> Yeah, I'm able to see exactly which cell I'm in using the winALDL program.
>  When I'm in gear, it's in a different cell, and things seem normal.  When
> I go to park, it switches to another cell and the BLMs in that cell go way
> up.  I'm not just looking at a BLM stream, I'm looking at a table of
> recent or averaged BLM values as a function of VE table cell.
>
> I could just try to tune it out with the VE table, but I find it hard to
> believe that the table is nearly perfect everyplace except one cell which
> is way, way off.  Has anyone on the list had such a thing; where the
> factory table was almost perfect except for one or two cells?
>
> Thanks for the help.
>
> > You need to look at RPM and MAP both at idle in neutral and in gear.
Your
> > VE map is ok when you
> > are in gear, but when you put it into neutral or park, the vacume goes
up
> > and the point on your ve map where
> > it's idling in neutral or park is too high (The ve) reduce that part of
> > the
> > map until your BL comes back down
> > to 128.
> > Mark
> > ----- Original Message -----
> > From: "Charles McDowell" <charles at taildragger.info>
> > To: <gmecm at diy-efi.org>
> > Sent: Thursday, August 18, 2005 7:49 PM
> > Subject: [Gmecm] 7747 High BLM at idle
> >
> >
> >> My truck has been running okay, but I finally decided to get around to
> >> gathering some more data to fine tune things.  I hooked up winALDL and
> >> drove
> >> around for a while.  As I drive around, all the BLM table values in
> >> winALDL
> >> show 124-133 or so - not bad really.  The weird thing is that when I
> >> pull
> >> in
> >> someplace, put it in park and idle it, the idle BLM cell (800/30 in
> >> winALDL)
> >> just climbs and climbs up to almost 150.  That same cell shows
something
> >> like 133 if I look at it before starting to idle.
> >>
> >> Any ideas what this could be, or where to even start looking?  It's a
> >> 7747
> >> for a SBC 350 with automatic, converted from carb.
> >>
> >> TIA
> >>
> >>
> >> _______________________________________________
> >> Gmecm mailing list
> >> Gmecm at diy-efi.org
> >> http://lists.diy-efi.org/mailman/listinfo/gmecm
> >>
> >
> > _______________________________________________
> > Gmecm mailing list
> > Gmecm at diy-efi.org
> > http://lists.diy-efi.org/mailman/listinfo/gmecm
> >
>
> _______________________________________________
> Gmecm mailing list
> Gmecm at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/gmecm

_______________________________________________
Gmecm mailing list
Gmecm at diy-efi.org
http://lists.diy-efi.org/mailman/listinfo/gmecm