[Diy_efi] 94-95 5.0 Mustang and a hanging idle...

Keith Varin keithvarin
Wed Jun 14 02:54:50 UTC 2006


I am using the TwEECer R/T system to tune my car. I just picked one up from
www.promustangperformance.com however i am still new to the unit and have
not really gotten a grasp of what settings do what. As far as adjusting the
idle... I've set the idle adjustment screw so that the car runs and to
temporaily get around the hanging idle issue i have actually unplugged the
IAC motor. I tried replacing it, however it made no difference. Im just
wondering why this happened after I installed  throttle body, and why it
only reacts the way it does when it id raining out...

Keith

On 6/13/06, Daniel Nicoson <A6intruder at myo-p.com> wrote:
>
> Keith,
>
> What have you done to adjust the idle with the new throttle
> body?  Normally,
> you would disconnect the ignition spout connector, disconnect the IAC and
> then manually adjust the throttle plate one "screw-turn" off closed.  Then
> adjust the idle bleed screw so the engine will idle without any computer
> help (this would be with every load off, defroster to off, lights off
> etc.)
>
> Once you get it to idle like this (fully warmed up), then turn off and
> plug
> all back in.  See if it is better then.
>
> If you were tuning the computer with a TwEECer or similar device then we
> could do more but if you are not modifying computer settings, not much
> else
> you can do.
>
> HTH,
>
> Dan Nicoson
>
> -----Original Message-----
> From: diy_efi-bounces at diy-efi.org [mailto:diy_efi-bounces at diy-efi.org]On
> Behalf Of Keith Varin
> Sent: Tuesday, June 13, 2006 10:08 PM
> To: Diy_efi at diy-efi.org
> Subject: [Diy_efi] 94-95 5.0 Mustang and a hanging idle...
>
> Hey everyone. First I would like to thank you all for viewing this thread.
>
> I have a 1994 Ford Mustang Cobra with the 5.0 GT-40 motor and a manual
> transmission. It is still relativly stock however with a few small mods I
> began to have a hanging idle. After installing a new TB and headers the
> idle
> would hang around 1800 rpms. my first thought was that i probably had a
> leak
> in the intake tract somewhere. So i disassembled the intake and resealed
> everything with rtv and high-tack gasket sealer. The problem went away, so
> I
> figured I had fixed it.Low and behold, 3 days later it was raining out and
> I
> began my 17 mile trip to work. Halfway there I realized that my car was
> still idling around 1800rpms, so the work I had done did not fix the
> problem.
>
> I have since paid close attention to the conditions of the environment and
> of my vehicle when the idle stays high, here is what I have figured out.
>
> When moving at any speed greater than 15mph with the vehicle in neutral or
> with the clutch pressed, the car will idle at or around 1100 rpms, and
> when
> the vehicle comes to a stop it will idle at 800-900 (which is normal).
> However, any time it is raining or very damn outside the car will idle at
> 1800rpms at any speed 15mph or greater with the vehicle in neutral or with
> the clutch pressed.
>
> If anyone has any input on why my car might be doing this or any ideas on
> ways to fix this problem. please feel free to shout it out.
>
> Thanks
> Keith
> _______________________________________________
> Diy_efi mailing list
> Diy_efi at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>
> _______________________________________________
> Diy_efi mailing list
> Diy_efi at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>




More information about the Diy_efi mailing list