[Diy_efi] TPI Question

[Mike Fisher]

Ok, so AUJM was the last MAF code.  I ordered a programmer and an Atmel
chip that thirdgen shows will work to program BINs to.  I am going to keep
the original chip and not mess with it, so I can always fall back on it.

On Tue, Oct 30, 2012 at 11:23 AM, Mike Fisher <mike.fisher at greenbush.org>wrote:

> If I remember right, the 89 anjf programming did away with the cold start
> injector.  I am mostly just wanting to get rid of that, and turn off vats
> and knock.  The application will be used for drag race only, so it will be
> full throttle or nothing.
> On Oct 30, 2012 11:03 AM, "Bill Hamilton" <scoutii76 at hotmail.com> wrote:
>
>>  What do you consider the latest MAF code.
>> If not a code for the 7165 then it can't be used in the 7165 AFAIK.
>> There are a few ECM/PCM that share hardware like the 7727/7730/7749 or
>> 7060/7427/6395 that can share bin codes but I do not know of any that share
>> with the 7165 that would actually gain you anything.
>> The gears are compensated for in the DRAC/VSSB and there are programming
>> options for manual and autos since GM used both.
>> Unless someone wants to retype it all, I would recommend heading over to
>> www.thirdgen.org and read up on their programming FAQs.
>> Most I see that used to run the 7165 end up swapping it out for something
>> newer.
>>
>> ------------------------------
>> Date: Tue, 30 Oct 2012 08:18:03 -0500
>> From: mfisher at ckt.net
>> To: diy_efi at diy-efi.org
>> Subject: Re: [Diy_efi] TPI Question
>>
>> Nobody has any thoughts?
>> On Oct 22, 2012 10:33 PM, "Mike Fisher" <mfisher at ckt.net> wrote:
>>
>> Alright guys, to add to this conversation....  I found my old 1227165 ECM
>> and ABWT MAF memcal.  Here is my next question on this one.  Can these be
>> reprogrammed to the latest MAF code?  And can it be programmed for gears,
>> manual shift, etc?  I am just not sure what my options are.  Since I am not
>> sure what mods have been done with this engine I am using, it may just be
>> better to use a MAF setup since it will adjust better without having to be
>> fine tuned as much.
>>
>> On Wed, Oct 17, 2012 at 10:49 PM, Brian Koontz <brian at pongonova.net>wrote:
>>
>> On Wed, Oct 17, 2012 at 08:37:18PM -0700, Bill Hamilton wrote:
>> >
>> > ATSN shows as 1990 3.1 auto16197128 ecmI have an excell spread sheet
>> > on binderplanet. I think it was originally on Moates before his
>> > crash.
>>
>> It's probably the same one.  I should work on getting all that data
>> online in a format that's updatable, because my copy has all sorts of
>> little notations and whatnot.
>>
>>   --Brian
>> _______________________________________________
>> Diy_efi mailing list
>> Diy_efi at diy-efi.org
>> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>>
>>
>>
>> --
>> Mike Fisher
>> Network Administrator
>> Southeast Kansas Education Service Center
>> http://helpdesk.greenbush.org
>> (620) 724-6281
>>
>> This message is from the Southeast Kansas Education Service Center. This
>> message and any attachments may contain information that is confidential
>> and/or legally privileged. It is intended only for the use of the
>> individual(s) and entity named above as the recipient of the message. If
>> you are not the intended recipient of this message, or if this message has
>> been addressed to you in error, please notify the sender immediately. We
>> ask that you please delete this message, and do not deliver, distribute or
>> copy the message or any attachments. Thank you.
>>
>>
>> _______________________________________________ Diy_efi mailing list
>> Diy_efi at diy-efi.org http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>> _______________________________________________
>> Diy_efi mailing list
>> Diy_efi at diy-efi.org
>> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>> --
>> Mike Fisher
>> Network Administrator
>> Southeast Kansas Education Service Center
>> http://helpdesk.greenbush.org
>> (620) 724-6281
>>
>> This message is from the Southeast Kansas Education Service Center. This
>> message and any attachments may contain information that is confidential
>> and/or legally privileged. It is intended only for the use of the
>> individual(s) and entity named above as the recipient of the message. If
>> you are not the intended recipient of this message, or if this message has
>> been addressed to you in error, please notify the sender immediately. We
>> ask that you please delete this message, and do not deliver, distribute or
>> copy the message or any attachments. Thank you.
>>
>>  <http://lists.diy-efi.org/mailman/listinfo/diy_efi>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.diy-efi.org/pipermail/diy_efi/attachments/20121031/093966ff/attachment.html