[Diy_efi] TPI Question

[Avery Nisbet]

A memcal from a V8 7730 or 7727 will work for sure.  There are some
other ECM's that are basically the same but I don't remember their
numbers off the top of my head.  The 7730 and the 7727 are the same,
one is just the under hood version.

If you look on ebay the V8 memcals are all V6's that have some
resistors soldered on them to "Make" them V8 memcals.  But the knock
stuff does not work on them.


If you search on http://www.thirdgen.org/ you can find out how to
change the V6 to V8 memcals.

-Avery

On Wed, Oct 17, 2012 at 12:47 PM, Mike Fisher <mfisher at ckt.net> wrote:
> So, in other words, I have to come up with a MEMCAL from a 7730 ECM to be
> able to use the AUJP code.  What else had 7730 V8 memcals?
>
>
> On Wed, Oct 17, 2012 at 2:28 PM, Bill Hamilton <scoutii76 at hotmail.com>
> wrote:
>>
>> "They are not interchangeable."
>>
>> No. Each application uses it's own code. The bin must match the code.
>> The TPI 7730 is normally a $8d code and the 7747 is a $42 code.
>> You can't run one bin with another code.
>> If you want a 5.7 TPI bin I have some, including the AUJP. It was the most
>> popular bin back in the day and was hacked pretty good. To include several
>> versions of a super AUJP.
>> IIRC there are MAF and MAP versions also.
>>
>> ________________________________
>> Date: Wed, 17 Oct 2012 13:39:34 -0500
>> From: mfisher at ckt.net
>> To: diy_efi at diy-efi.org
>>
>> Subject: Re: [Diy_efi] TPI Question
>>
>> But the question is can they be reprogrammed with a 7730 bin?
>>
>> On Wed, Oct 17, 2012 at 12:40 PM, Bill Hamilton <scoutii76 at hotmail.com>
>> wrote:
>>
>> Thise are 1227747 bins.
>> You are asking for 1227730 bins.
>> They are not interchangeable.
>>
>> ________________________________
>> Date: Wed, 17 Oct 2012 11:05:30 -0500
>> From: mfisher at ckt.net
>> To: davida1 at hiwaay.net
>> CC: diy_efi at diy-efi.org
>>
>> Subject: Re: [Diy_efi] TPI Question
>>
>> So, I did come up with these codes being 5.7L truck engine codes.  Will
>> any of these work for a 7730 ECM?  I think I have an ANLZ at home if I
>> remember right.  Or are they all the same sockets on other ECM's?  Sorry, I
>> am still learning some of this.
>>
>> ACSU, ACSW, AKAL, AKAJ, AKAR, AMUR, ANLW, ANLX, ANLZ, ARHT, ARJT, ARJU,
>> ASDU, ASDW, ASDZ
>>
>> On Wed, Oct 17, 2012 at 10:25 AM, David Allen <davida1 at hiwaay.net> wrote:
>>
>> I would be happy to erase and reprogram one for you, if you have a V8 one!
>>
>> I beleive I have already a copy of the AUJP program.
>>
>> ----- Original Message -----
>> From: Mike Fisher
>> To: diy_efi at diy-efi.org
>> Sent: Wednesday, October 17, 2012 10:20 AM
>> Subject: Re: [Diy_efi] TPI Question
>>
>> So, I guess the next question, if you can find a stock memcal to use,
>> which ones will work?  Any standard numbers that I could use?  And if I can
>> get one, would anyone on the list be up to flashing one for me to get back
>> up and running until I can pick up a programmer?
>>
>> On Wed, Oct 17, 2012 at 10:00 AM, Aaron <aaron at creativeoverdrive.com>
>> wrote:
>>
>> This is what I use to reprogram the 7747 GM ECU?s
>> http://www.moates.net/apu1-autoprom-package-usb-version.html
>>
>> Since the original sized / pinned chip is getting difficult to find new, I
>> use these to use a larger chip.
>> http://www.moates.net/g2-memory-adapter-0-60-leg-spacing.html
>>
>> With the above hardware and provided software, you can start with the AUJP
>> code and adapt it to your needs.
>> Like this ?
>> http://www.diy-efi.org/gmecm/ecm_info/1227730/qanda.html
>>
>> Good luck and send us updates.
>> It gets lonely here when no one posts.
>>
>>
>> From: diy_efi-bounces at diy-efi.org [mailto:diy_efi-bounces at diy-efi.org] On
>> Behalf Of Mike Fisher
>> Sent: Wednesday, October 17, 2012 10:27 AM
>>
>> To: Do It Yourself fuel injection
>> Subject: [Diy_efi] TPI Question
>>
>> Since joining this list over a year ago, I think I had only seen one email
>> until the past week.  So, I am going to re-ask a question I asked a while
>> back that I really didn't get any response to.
>>
>> I have a 91 Tuned Port Injection setup from a Firebird that I installed on
>> my 87 Mustang GT that I drag race with a 355 small block in it.  I was
>> running a stock AUJP chip that a friend of mine had, but he needed it back a
>> few months ago (since they are getting hard to find).  Anyway, what I am
>> wondering is if there is a way to program another chip with the AUJP code,
>> or anything better to run a TPI system with?  I have seen that people have
>> reprogrammed some of the V6 chips with the AUJP code on Ebay, but wonder if
>> they actually will work right.  Thanks!
>>
>> Mike
>>
>> _______________________________________________
>> Diy_efi mailing list
>> Diy_efi at diy-efi.org
>> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>>
>>
>>
>> Diy_efi mailing list
>> Diy_efi at diy-efi.org
>> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>>
>>
>>
>>
>>
>> _______________________________________________ Diy_efi mailing list
>> Diy_efi at diy-efi.org http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>> _______________________________________________
>> Diy_efi mailing list
>> Diy_efi at diy-efi.org
>> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>>
>>
>>
>> --
>> Mike Fisher
>> Network Administrator
>> Southeast Kansas Education Service Center
>> http://helpdesk.greenbush.org
>> (620) 724-6281
>>
>> This message is from the Southeast Kansas Education Service Center. This
>> message and any attachments may contain information that is confidential
>> and/or legally privileged. It is intended only for the use of the
>> individual(s) and entity named above as the recipient of the message. If you
>> are not the intended recipient of this message, or if this message has been
>> addressed to you in error, please notify the sender immediately. We ask that
>> you please delete this message, and do not deliver, distribute or copy the
>> message or any attachments. Thank you.
>>
>> _______________________________________________ Diy_efi mailing list
>> Diy_efi at diy-efi.org http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>> _______________________________________________
>> Diy_efi mailing list
>> Diy_efi at diy-efi.org
>> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>>
>
>
>
> --
> Mike Fisher
> Network Administrator
> Southeast Kansas Education Service Center
> http://helpdesk.greenbush.org
> (620) 724-6281
>
> This message is from the Southeast Kansas Education Service Center. This
> message and any attachments may contain information that is confidential
> and/or legally privileged. It is intended only for the use of the
> individual(s) and entity named above as the recipient of the message. If you
> are not the intended recipient of this message, or if this message has been
> addressed to you in error, please notify the sender immediately. We ask that
> you please delete this message, and do not deliver, distribute or copy the
> message or any attachments. Thank you.
>
> _______________________________________________
> Diy_efi mailing list
> Diy_efi at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/diy_efi
>