From andreic at chichak.ca Sat Nov 4 15:38:07 2006 From: andreic at chichak.ca (Andrei Chichak) Date: Sat, 04 Nov 2006 14:38:07 -0700 Subject: [Efi332] The original stimulator board Message-ID: <7.0.1.0.0.20061104140705.0204e260@chichak.ca> Hi there, I think this question is actually for Jeff (maybe not). Does anybody have the schematics and instructions for the original stimulator board (4 caps, 4 resistors, 1 555, 1 pic, 1 crystal, no LEDs)? I am finally getting around to putting it together and I find that I don't have any component placement info. Thanks, Andrei ------------------------------ Andrei Chichak 4024-120 Street Edmonton, Alberta Canada T6J 1X8 (780)434-6266 Lat: 53? 28' 40" N Lon: 113? 32' 27" W '62 Morris Traveller + 1275 Cooper 'S engine '97 Volvo 850 '99 VW Golf From bowtievette at aol.com Sat Nov 4 22:47:57 2006 From: bowtievette at aol.com (BowTie Vette) Date: Sat, 4 Nov 2006 20:47:57 -0800 Subject: [Efi332] The original stimulator board In-Reply-To: <7.0.1.0.0.20061104140705.0204e260@chichak.ca> References: <7.0.1.0.0.20061104140705.0204e260@chichak.ca> Message-ID: Hello Andrei, See if this helps... Parts List QuantityBoard IDDescription 1R21.3kW ?W resistor 1 R31.0kW 1/4W resistor 3C1,C2,C30.01 m F cap 1C40.2 m F cap 5BARO, COOLANT, TPS, AIRTEMP, MAP 10kW Linear Taper Potentiometer 1RPM50kW Audio Taper Potentiometer 1R8330W ?W Resistor 1R1010kW Resistor 3J1,J2,J320X1 Male Header 1IC2PIC16C56 Microcontroller 1U2LM555CN Timer 1U$24.0 MhZ Can Oscillator 1X2DB37 male connector 3NoneJumpers 1NoneQuad Terminal Block 1NoneFemale 2.0 mm power connector Jeff In a message dated 11/04/06 13:38:38 Pacific Standard Time, andreic at chichak.ca writes: Hi there, I think this question is actually for Jeff (maybe not). Does anybody have the schematics and instructions for the original stimulator board (4 caps, 4 resistors, 1 555, 1 pic, 1 crystal, no LEDs)? I am finally getting around to putting it together and I find that I don't have any component placement info. Thanks, Andrei -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.diy-efi.org/pipermail/efi332/attachments/20061104/b66e6e32/attachment.html -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 40086 bytes Desc: not available Url : http://lists.diy-efi.org/pipermail/efi332/attachments/20061104/b66e6e32/attachment.gif From andreic at chichak.ca Sat Nov 4 22:45:28 2006 From: andreic at chichak.ca (Andrei Chichak) Date: Sat, 04 Nov 2006 21:45:28 -0700 Subject: [Efi332] The original stimulator board In-Reply-To: References: <7.0.1.0.0.20061104140705.0204e260@chichak.ca> Message-ID: <7.0.1.0.0.20061104214230.02129710@chichak.ca> At 09:47 PM 11/4/2006, you wrote: >Hello Andrei, >See if this helps... YES, the parts list is just what I needed. The schematic doesn't match but I'll see what I can do to figure out what goes where and what the jumper block does. Thanks, Andrei >Jeff ------------------------------ Andrei Chichak 4024-120 Street Edmonton, Alberta Canada T6J 1X8 (780)434-6266 Lat: 53? 28' 40" N Lon: 113? 32' 27" W From KevinY at cybertech.ca Mon Nov 6 12:04:34 2006 From: KevinY at cybertech.ca (Kevin Yachimec) Date: Mon, 6 Nov 2006 11:04:34 -0700 Subject: [Efi332] The original stimulator board References: <7.0.1.0.0.20061104140705.0204e260@chichak.ca> <7.0.1.0.0.20061104214230.02129710@chichak.ca> Message-ID: <6CA6CDF92F4DAA4B8A43738591E06C130ABF62@cyb-e004.cyb-edm.local> I think I might have the pic program but there wasn't much to it. Do you want me to look for it? -Kevin -----Original Message----- From: efi332-bounces at diy-efi.org on behalf of Andrei Chichak Sent: Sat 11/4/2006 9:45 PM To: efi332 at diy-efi.org Subject: Re: [Efi332] The original stimulator board At 09:47 PM 11/4/2006, you wrote: >Hello Andrei, >See if this helps... YES, the parts list is just what I needed. The schematic doesn't match but I'll see what I can do to figure out what goes where and what the jumper block does. Thanks, Andrei >Jeff ------------------------------ Andrei Chichak 4024-120 Street Edmonton, Alberta Canada T6J 1X8 (780)434-6266 Lat: 53? 28' 40" N Lon: 113? 32' 27" W _______________________________________________ Efi332 mailing list Efi332 at diy-efi.org http://lists.diy-efi.org/mailman/listinfo/efi332 -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/ms-tnef Size: 2983 bytes Desc: not available Url : http://lists.diy-efi.org/pipermail/efi332/attachments/20061106/3de686f4/attachment.bin From andreic at chichak.ca Mon Nov 6 12:27:43 2006 From: andreic at chichak.ca (Andrei Chichak) Date: Mon, 06 Nov 2006 11:27:43 -0700 Subject: [Efi332] The original stimulator board Message-ID: <7.0.1.0.0.20061106112135.01f02658@chichak.ca> Hey Kevin, No, I'm good now. Jeff got me everything I need. It was mostly the resistor positions I needed. I've got my TWD120 oscilloscope fired up and I'll be testing it later today. Thanks, Andrei On 11/6/2006 11:04:34 AM, Kevin Yachimec (keviny at cybertech.ca) wrote: > I think I might have the pic program but there wasn't much to it. > > Do you want me to look for it? > > -Kevin ------------------------------ Andrei Chichak 4024-120 Street Edmonton, Alberta Canada T6J 1X8 (780)434-6266 Lat: 53? 28' 40" N Lon: 113? 32' 27" W '62 Morris Traveller + 1275 Cooper 'S engine '97 Volvo 850 '99 VW Golf