intergrator and BLM

[Dr.Acacio]

Where I can find the anht dissasembly file????
Is there any information about where is the Fan temp starting address????
Could be used this information to discover where is in the BDZL file the fan
start temp address?????

-----Mensagem Original-----
De: CSH-HQ <nacelp at jvlnet.com>
Para: <gmecm at efi332.eng.ohio-state.edu>
Enviada em: Quarta-feira, 3 de Novembro de 1999 18:08
Assunto: RE: intergrator and BLM


> Careful, on some of the f-body/vette some of the tables are the same but
> some of the switches are different (rad fan comes to mind).
> Grumpy
>
>
> Code and tables are on the eprom that is on your
> >memcal unit.  the tables start at 0 and the code
> >starts at 3000H (in the eprom).  If you are serious
> >about modifying your code, download the anht
> >dissasembly from ecmguy.  all of the tables are in the
> >exact same locations as your aujp(?).  There are also
> >descriptions of most tables.
> >
> >Squash
> >
> >--- Mike Rolica <mrolica at meridian-mag.com> wrote:
> >> Like I said to bruce, I don't like clutter.  Where
> >> is the code stored on the
> >> 730? Physically and address? -address? Is it like
> >> the 165 and very similar
> >> to the 68hc11f1 Motorola microcontroller?
> >> Mike Rolica
> >> EXT. 260
> >>  :-)
> >>
> >>
> >> -----Original Message-----
> >> From: David Cooley [SMTP:n5xmt at bellsouth.net]
> >> Sent: Wednesday, November 03, 1999 1:11 PM
> >> To: gmecm at efi332.eng.ohio-state.edu
> >> Subject: Re: intergrator and BLM
> >>
> >> At 12:56 PM 11/3/1999 -0500, you wrote:
> >> >OK, staying on this thread, How large is the BLM
> >> on a 90 730 on a
> >> f-body?
> >> >Can it be enlarged from lets say 16 to 32 as to
> >> give a finer
> >> resolution?
> >> >Does this make sense?, Also, can some of the fuel
> >> map tables
> >> PE/tables be
> >> >enlarged to a finer resolution at cruise rpm, in
> >> my instance
> >> 1500-2600?  I
> >> >know that the prom/memcal is pretty full but can
> >> some of this stuff
> >> be
> >> >scraped because it is not used? Ie shift light
> >> stuff, ccp, air
> >> injection?
> >> >Too free up space?
> >>
> >>
> >> It could probably be done, but you just can't scrap
> >> the tables...
> >> The code
> >> will be looking for data in those locations.  You'd
> >> need to totally
> >> re-write the code.
> >> Why not just go to a newer PCM with more PROM space
> >> and customize
> >> from there?
> >>
> >>
> >>
> >===========================================================
> >> David Cooley N5XMT Internet: N5XMT at bellsouth.net
> >> Packet: N5XMT at KQ4LO.#INT.NC.USA.NA T.A.P.R. Member
> >> #7068
> >> We are Borg... Prepare to be assimilated!
> >>
> >>
> >===========================================================
> >>
> >
> >
> >=====
> >
> >__________________________________________________
> >Do You Yahoo!?
> >Bid and sell for free at http://auctions.yahoo.com
> >
>