How to do 165 to 730

[Romans, Mark]

All vet's, 84 on had digital dashes.
90 kind of went to a hybrid that was still digital on the dash.
Mark
----- Original Message -----
From: "Bruce Plecan" <nacelp at bright.net>
To: <gmecm at diy-efi.org>
Sent: Tuesday, June 27, 2000 7:47 PM
Subject: Re: How to do 165 to 730


>
> Why'd ya do the extra work?
> Hmm is your's a digitial dash?.
>
> The "normal" operation of the 165 uses a VSS in the speedo head, in which
> case as long as you had a speedo cable you'd be fine.
>
> The 90 730 uses a A/C generator to buffer to ecm.
>
> For a 730 to use the speedo VSS, there is a bit and wire change for it to
> work.
>
> Just dawned on me with that tranny you may be using a reluctor output to
> buffer and doing the same thing as the digital dash F-Bodies did, rare for
> the F-Bodies, don't know how common in the vettes.
> Grumpy
>
>
>
>
> > I have a 90 ZF6 trans using the stock 90 vss feeding the 165 ecm and the
> > speedo runs perfect.  Maybe vet's are different.
> > Mark
> > ----- Original Message -----
> > From: "Bruce Plecan" <nacelp at bright.net>
> > To: <gmecm at diy-efi.org>
> > Sent: Tuesday, June 27, 2000 2:21 PM
> > Subject: Re: How to do 165 to 730
> >
> >
> > >
> > > > If I wanted to change my 87 Vette to 730, how would I do it, in
> > > > general.
> > > > Do I need to change a lot of wiring/connectors?
> > > > No... just need to take all the pins out of the 165 harness, and put
> > > > then in the 730 connector.
> > > > I just use the wiring diagram  which I still have to find (think is
> > > > on ftp site) find it on 165 diag, and 730 and swap.. I used the
wires
> > for
> > > > the maf so that I did not have to add any.
> > > > Do I need to add any
> > > > other sensors besides the MAP?
> > > > Nope
> > > > Where does the MAP go and how do I put it
> > > > there?
> > > > I put mine on fire wall.. use the oem hose from map and stick it on
> > > > one of the vacume ports on ps near rear...
> > > > FPR gets the vac signal from same spot.
> > > > Thanks.
> > >
> > > will take a *custom* chip for the VSS in you 87.
> > > Grumpy
> > >
> >
>
> --------------------------------------------------------------------------
> > --
> > > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
quotes)
> > > in the body of a message (not the subject) to
> majordomo at lists.diy-efi.org
> > >
> > >
> >
>
> --------------------------------------------------------------------------
> --
> > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> > in the body of a message (not the subject) to
majordomo at lists.diy-efi.org
> >
>
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo at lists.diy-efi.org
>
>

----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org