Need small IAC

[Swayze]

91vette is a little over 1" diameter with ears opposite each other (out to
out app2"). height is about 1-1/4". the cone is about 1-2 to 3/4" below
this. I'm kinda a newbie, so my knowledge is limited.I can measure it when I
get home.
byE
Mike
Swayze
mswayze at truswood.com
kswayze at bellsouth.net

----- Original Message -----
From: "Eric Norgard" <eric at aztek-eng.com>
To: <gmecm at diy-efi.org>
Sent: Friday, October 27, 2000 3:33 PM
Subject: Re: Need small IAC


> No picture. It's in the design phase at this time. I'll design it to what
I
> can get for an IAC. The smaller the better.
>
> Eric
>
> Swayze wrote:
> >
> > got a pic of the TB?
> > Swayze
> > mswayze at truswood.com
> > kswayze at bellsouth.net
> > <8-{b>
> > ----- Original Message -----
> > From: "Eric Norgard" <eric at aztek-eng.com>
> > To: "gmecm" <gmecm at diy-efi.org>
> > Sent: Friday, October 27, 2000 1:48 PM
> > Subject: Need small IAC
> >
> > > I'm currently in the process of building a throttle body for my PFI
system
> > and
> > > I need a IAC. I'm looking for an IAC that would be small and mount on
> > > to the throttle body. Any recommendations on a vehicle that would work
and
> > or
> > > a source for them. If it makes any diffence, I'm running the 730 ECU.
> > >
> > > Thanks
> > > Eric
> > >
> > > --
> > >
> > > Eric Norgard
> > > Software Engineer           Voice: 303-415-6146 (Direct)
> > > Aztek Engineering Inc.             303-786-9100 (Receptionist)
> > > 2477, 55th St., Suite 202   Fax  : 303-786-9190
> > > Boulder, CO 80301-2835      Email: Eric.Norgard at aztek-eng.com
> >
> --------------------------------------------------------------------------
> > --
> > > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
quotes)
> > > in the body of a message (not the subject) to
majordomo at lists.diy-efi.org
> > >
> > >
> >
>
> --------------------------------------------------------------------------
--
> > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> > in the body of a message (not the subject) to
majordomo at lists.diy-efi.org
>
> --
>
> Eric Norgard
> Software Engineer           Voice: 303-415-6146 (Direct)
> Aztek Engineering Inc.             303-786-9100 (Receptionist)
> 2477, 55th St., Suite 202   Fax  : 303-786-9190
> Boulder, CO 80301-2835      Email: Eric.Norgard at aztek-eng.com
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo at lists.diy-efi.org
>
>

----- End of forwarded message from owner-gmecm at diy-efi.org -----
----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org