DIY EFI on 400ci smallblock?

[Hector]

I'm going to convert to EFI a similar engine: 10:1, 64 cc  AL heads, 404 ci,
home made PFI. I had been looking at the AUJP as a base but considering that
a Vette engine had AL heads and such, I'm now thinking the ANHT. Mainly for
the timing tables. Oh yeah, and for the limp mode as I need a calmap anyhow.

Hector
http://soflaspeed.freeservers.com


----- Original Message -----
From: "Len Sabatine" <sabatine at epix.net>
To: <gmecm at diy-efi.org>
Sent: Monday, June 18, 2001 11:20 PM
Subject: Re: DIY EFI on 400ci smallblock?


>      Starting with *8 Injectors [ Port ]  , an 8262 ECM , and AUJP as a
base,
>      will produce much more satisfying results IMHO.
>
>    Len
>
>
> >List,
> >
> >I have been trying to grasp DIY EFI by reverse engineering the code
> >my P4 ECM out of an 88 4cyl fiero, and so far it has been quite
> >frustrating/unbeneficial.  I understand the assembly code just fine,
> >but not the ability to truely reverse engineer it and understand what
> >it's actually doing - it's difficult to recognize the purpose of most of
> >the subroutines and code.  I've kind of given up on this project for
> >now.
> >
> >That doesn't mean i'm out of projects, yet.  :)  I am in a buildup
> >process of a 400ci smallblock chevy bound for a 71 camaro, and
> >i'm wondering about the prospects of converting it to a '747 TBI
> >setup.  I'm thinking a project like this should be a LOT easier, given
> >the large amount of knowledge and work already gone into the '747
> >ecm, as opposed to some 4cyl ECM nobody cares about!  :)
> >
> >Question is, how much motor can the 747 ECM be made to deal
> >with?  Here's what I've got, if anyone with some knowledge of what
> >the 747 can and cannot do (or good/bad uses of it) could let me
> >know if i'm barking up the right or wrong tree, would be greatly
> >appreciated!!
> >
> >10:1 400ci smallblock chevy w/ 5.7" rods
> >
> >GM's 'fast burn' alum heads (the 210cc intake runner heads) in as-
> >cast configuration with stock valves (2.00/1.55) with valvesprings
> >appropriate for my cam choice
> >
> >exhaust will be headers with 1 3/4" primaries, full length tubes, to a
> >2.5" dual exhaust with full tailpipes and crossover pipe
> >
> >performer RPM air gap for the vortec head bolt pattern
> >
> >cam is mech. roller, 232/240 @ 0.050", 0.505"/0.523" net lift, 112
> >degrees lobe sep angle
> >
> >and all the necessary high quality fasteners, machine work,
> >attention to detail and clearances, etc. to make it a reliable
> >street/strip motor...  oh yeah, the car is a manual tranny car, 4spd
> >for now, oneday to be a 5spd or 6spd but definately always a
> >manual.
> >
> >Basically, it's a ZZ430 crate motor with 50 more cubic inches, a bit
> >better intake, and a bit bigger cam.  If the ZZ430 was capable of
> >430HP   out of 350ci, I reasonably anticipate an honest 450HP if not
> >a bit more out of this 400.
> >
> >So, anyhow.  Is this a good candidate for a '747 TBI setup?  Can a
> >'747 run a 4bbl TBI?  Can the '747 deal with a moderate cam that
> >may not idle like a swiss timepiece?
> >
> >Any comments greatly appreciated!!!!
> >
> >nick
>

----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org