[Gmecm] SEQUENTIAL INJECTION FOR TPI

[D.Pray]

The price is $379.00 and that includes the position sensor and rotor.

Dwight Pray, Chief Engineer
BAK Engineering, LLC
www.bakengineering.com
tel:407-324-2907
fax:407-268-4874
When the solution is simple, God is answering. A. Einstein


----- Original Message ----- 
From: "Justin justin" <justin_email at lycos.com>
To: <gmecm at diy-efi.org>
Sent: Tuesday, May 03, 2005 3:01 PM
Subject: Re: [Gmecm] SEQUENTIAL INJECTION FOR TPI


  How much does this system cost?  Also whats included with it?  Do you have
to buy the cam position sensor separately?  Will this system work with a cam
sensor from a cadillac 4.9 liter?  - Justin
----- Original Message -----
From: "D.Pray" <dpray at cfl.rr.com>
To: gmecm at diy-efi.org, Brandon_Tomlinson at baylor.edu
Subject: Re: [Gmecm] SEQUENTIAL INJECTION FOR TPI
Date: Tue, 3 May 2005 14:51:21 -0400

>
> It should work fine as long as you have a distributor to install the
> position sensor.  Our system is configurable for 4, 6, or 8 cylinders.
>
> Dwight Pray, Chief Engineer
> BAK Engineering, LLC
> www.bakengineering.com
> tel:407-324-2907
> fax:407-268-4874
> When the solution is simple, God is answering. A. Einstein
>
> ----- Original Message -----
> From: "Tomlinson, Brandon B." <Brandon_Tomlinson at baylor.edu>
> To: <gmecm at diy-efi.org>
> Sent: Tuesday, May 03, 2005 2:02 PM
> Subject: RE: [Gmecm] SEQUENTIAL INJECTION FOR TPI
>
>
> Dwight,
>
> That system looks very interesting.  Could your cam sensor be used in
> efi conversions?  I am still looking for a better system for my 83 Regal
> T-type.  The hold up has been the distributor. Nice work. Brandon
>
>
> -----Original Message-----
> From: gmecm-bounces at diy-efi.org [mailto:gmecm-bounces at diy-efi.org] On
> Behalf Of D.Pray
> Sent: Tuesday, May 03, 2005 11:49 AM
> To: D.Pray; gmecm at diy-efi.org
> Subject: [Gmecm] SEQUENTIAL INJECTION FOR TPI
>
> Our company has developed a sequencer that converts TPI (and other EFI
> systems) to sequential fuel injection.  It works with your existing ECM
> and
> MEMCAL. We will be testing the prototype tomorrow.  The price is
> significantly lower than converting to a completely new controller. Is
> there
> any interest out there?
>
> The system can be viewed at:
> http://www.bakengineering.com/page5.html
>
> Dwight Pray, Chief Engineer
> BAK Engineering, LLC
> www.bakengineering.com
> tel:407-324-2907
> fax:407-268-4874
> When the solution is simple, God is answering. A. Einstein
>
>
> _______________________________________________
> Gmecm mailing list
> Gmecm at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/gmecm
> _______________________________________________
> Gmecm mailing list
> Gmecm at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/gmecm
>
>
> _______________________________________________
> Gmecm mailing list
> Gmecm at diy-efi.org
> http://lists.diy-efi.org/mailman/listinfo/gmecm

-- 
_______________________________________________
NEW! Lycos Dating Search. The only place to search multiple dating sites at
once.
http://datingsearch.lycos.com

_______________________________________________
Gmecm mailing list
Gmecm at diy-efi.org
http://lists.diy-efi.org/mailman/listinfo/gmecm