[Gmecm] new member, Buick 3800 project

[David Allen]

Jay, yes I still have that tune!  It's on my other laptop that's still in 
the states.  When I get back from Holland I will e-mail it to you, and/or 
burn a chip.  Any of the 2732 chips will work as long as they are still good 
enough to erase and program over.

That will be one BAD corvair with a LG3 turbo engine!!!!

David

----- Original Message ----- 
From: "Jay Maechtlen" <jaysjunk9 at covad.net>
To: "David Allen" <davida1 at hiwaay.net>
Sent: Tuesday, September 20, 2011 9:16 PM
Subject: Re: [Gmecm] new member, Buick 3800 project


>I guess if you still have that tune around, I'd like to take you up on it!
>
> I have some eproms around if you need them - let me know.
> Will that work in this particular computer?
> 1227783
> Application:1987-88 3.8 V6 SFI ?3? LG3 (exc. ?E? body) (domestic)
> MEMPAK IDs:AFDL, AJSJ, AKAY, AKBA, ?
> CALPAK IDs:16036495
> Program ID:68 ($44)
> Pgm ID Addr:$3004
> Scan ID Addr:$3002:$3003
> EPROM type:2732
> EPROM offset:$3000
>
> On 1/11/2010 2:11 PM, David Allen wrote:
>> Jay - I have a turbocharged LG3 engine I'm tuning right now. It runs the
>> stock MAF and uses off-the-shelf injectors for a L67 engine. As-is it
>> supports 9 PSI without any trouble. I will burn you a copy of the chip if
>> you want it. Just ask! It is not a completely refined tune but it works
>> well enough. This tune will allow you to run the engine with a turbo and
>> intercooler, with the MAF between the intercooler and throttle-body. You
>> will have to install the L67 injectors for it to run but all other stuff 
>> is
>> stock.
>>
>> Here is a video of this engine propelling a 3200 Lb car:
>> http://www.youtube.com/watch?v=FN20IRp8ZLI
>>
>> That was 5 or less PSI. Now it's working well at 9. I am trying for 10 
>> PSI
>> but the wastegate is too weak and I need a different actuator can. Goal 
>> is
>> 240 HP which should take about 10 PSI on this engine.
>>
>> Take care,
>> David
>>
>>
>> ----- Original Message ----- From: "Jay Maechtlen" <jaysjunk9 at covad.net>
>> To: <gmecm at diy-efi.org>
>> Sent: Monday, January 11, 2010 3:03 PM
>> Subject: [Gmecm] new member, Buick 3800 project
>>
>>
>>> Hi, Everyone
>>> I'm following the discussions with interest, as my project car has a
>>> stock '87 GM 3800 in it.
>>> ('61 Corvair, FWD 3800+Th440T4 in rear)
>>> I used wiring harness and controls from the donor car (87 Olds Delta 
>>> 88).
>>> It works, but mondo ugly. The plans include a turbocharger (from 84
>>> Buick 3.8 T-Type in hand), and I imagine I'll need to go with bigger MAF
>>> and other changes at some point.
>>> I am glad to see that you have folks using MAF as well as SD systems.
>>> I'm in learn mode right now, probably 4-6 months from turbo and computer
>>> mapping.
>>> Best regards
>>> Jay
>>>
>>>
>>> _______________________________________
>>> No infection found in this outgoing message
>>> Scanned by iolo System Shield?
>>> http://www.iolo.com
>>>
>>> _______________________________________________
>>> Gmecm mailing list
>>> Gmecm at diy-efi.org
>>> http://lists.diy-efi.org/mailman/listinfo/gmecm
>>>
>>>
>>
>>
>> _______________________________________
>> No infection found in this incoming message
>> Scanned by iolo System Shield?
>> http://www.iolo.com
>>
>>
>
>
>