[Gmecm] PCM-6 Turbo

[David Allen]

Robert, I don't think I have the extra SRAM, I know my ECM is not modified in any way. I remember reading some details about your nAst1 calibration. Can you refresh my memory on where to read up on it? Thanks,
David


  ----- Original Message ----- 
  From: Robert Saar 
  To: gmecm at diy-efi.org 
  Sent: Thursday, November 08, 2012 5:51 PM
  Subject: Re: [Gmecm] PCM-6 Turbo


        David, if you're running a 16149396 or modded a 7730/7727 to have the extra SRAM in the 1800-1FFF range, you'll be able to basically copy/paste a lot of your current tune into a nAst1 BIN. it has quite a few features that normal A1 does not have.

        --- On Thu, 11/8/12, David Allen <davida1 at hiwaay.net> wrote:


          From: David Allen <davida1 at hiwaay.net>
          Subject: Re: [Gmecm] PCM-6 Turbo
          To: gmecm at diy-efi.org
          Date: Thursday, November 8, 2012, 3:26 PM


          Robert, I would love to see this. I have an $A1 turbocharged car now. I re-scaled it for 2-bar and it runs well, but yours sounds like a much better solution!
          Thanks,
          David
            ----- Original Message ----- 
            From: Robert Saar 
            To: gmecm at diy-efi.org 
            Sent: Wednesday, November 07, 2012 8:00 PM
            Subject: Re: [Gmecm] PCM-6 Turbo


                  assuming nobody else has, i wouldn't mind sharing the patch i made for nAst1 to allow up to 3BAR support. you may have to do some digging to find where to apply the jump/return locations, but otherwise it's been bench-tested.

                  the way i have it setup now, it accounts for fuel via a 2d table with 10kPa increments to 300kPa as a BPW mulitplier. for spark, i just have a basic "retard vs kPa" table that runs from 100 to 300kPa.

                  --- On Wed, 11/7/12, Bill Hamilton <scoutii76 at hotmail.com> wrote:


                    From: Bill Hamilton <scoutii76 at hotmail.com>
                    Subject: [Gmecm] PCM-6 Turbo
                    To: "gm ecm" <gmecm at diy-efi.org>
                    Date: Wednesday, November 7, 2012, 8:15 PM


                    Anyone played with the code for the PCM-6/7427/8625  etc... to allow 2 or 3 bar map for turbo application?
                     
                    I'm running the $0E with MPFI and the 4l80E but thinking of adding a turbo.
                    I've seen the WB code but haven't seen anyone mention turbo/supercharger addition.
                     
                    Thanks,
                    Bill USN-1


                    -----Inline Attachment Follows-----


                    _______________________________________________
                    Gmecm mailing list
                    Gmecm at diy-efi.org
                    http://lists.diy-efi.org/mailman/listinfo/gmecm
                 


--------------------------------------------------------------------

            _______________________________________________
            Gmecm mailing list
            Gmecm at diy-efi.org
            http://lists.diy-efi.org/mailman/listinfo/gmecm


          -----Inline Attachment Follows-----


          _______________________________________________
          Gmecm mailing list
          Gmecm at diy-efi.org
          http://lists.diy-efi.org/mailman/listinfo/gmecm
       



------------------------------------------------------------------------------


  _______________________________________________
  Gmecm mailing list
  Gmecm at diy-efi.org
  http://lists.diy-efi.org/mailman/listinfo/gmecm
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.diy-efi.org/pipermail/gmecm/attachments/20121108/0e167435/attachment-0001.html