<DIV>>We believe our DIY unit, when built, tested and <BR>>calibrated as we describe, are as good as the Motec and Autronic units <BR>>you'll pay up to AU$2,000 for.
<DIV> </DIV>
<DIV>That is quite a claim. What have you done to verify the accuracy of your unit? Have you built a gas bench to verify response time and accurate reporting of the AFR? What certified test equipment do you have? What test procedures have you used to verify the claims you are making? </DIV>
<DIV> </DIV>
<DIV>Have you had your WB unit independently verified by certified engineers?</DIV>
<DIV> </DIV>
<DIV>What type of environmental testing has been done on your units? Are all of the components used in your product been qualified for automotive use? Are the circuit boards conformal coated? What is the temperature range of the components used?</DIV>
<DIV> </DIV>
<DIV>Or is it just another 'hobby' product you as so famous for?</DIV>
<DIV> </DIV>
<DIV>Thanks for your time,</DIV>
<DIV> </DIV>
<DIV>Al.</DIV><BR><BR><B><I>Peter Gargano <peter@techedge.com.au></I></B> wrote:
<BLOCKQUOTE class=replbq style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid">Wayne Macdonald wrote:<BR>> Hi.<BR>> I have one of the first DIY-WB circuit boards that was designed for the <BR>> L1H1 wide band sensor.<BR>> Can I adapt this circuit board to use the cheaper Bosch wide band <BR>> sensors like the one found on the VW?<BR><BR>Wayne,<BR><BR>As much as I hate plugging our own product, as you are a fellow Aussi, <BR>I'll simply mention we do a DIY controller for the LSU sensor (in fact <BR>two DIY controllers, one with an inbuilt display). Our design is <BR>fairly mature and we have sold thousands as DIY kits. We also sell <BR>them pre-built. We also offer a fix-it service if you have trouble <BR>getting your unit to go (they are out of necessity complex pieces of <BR>equipment if they are to perform well).<BR><BR>As other will mention, there are a few people now who make low cost <BR>controllers for wideband sensors. Many are junk, and a
few are <BR>reasonably good. We believe our DIY unit, when built, tested and <BR>calibrated as we describe, are as good as the Motec and Autronic units <BR>you'll pay up to AU$2,000 for. I'd say our unit is better, but that <BR>would be a bit OTT.<BR><BR><BR>Peter Gargano<BR>--<BR>Tech Edge Pty. Ltd. http://techedge.com.au http://WBo2.com<BR>ph : (02) 6251 5519 Int'l : +612 6251 5519 Fax : +612 6251 0558<BR>Street addr : 37 Jalanga Cres., Aranda, ACT 2614, Australia<BR>Postal addr : PO Box 288, Jamison Centre, ACT 2614<BR><BR><BR><BR><BR><BR><BR>te.<BR><BR>_______________________________________________<BR>Wbo2 mailing list<BR>Wbo2@diy-efi.org<BR>http://lists.diy-efi.org/mailman/listinfo/wbo2<BR></BLOCKQUOTE></DIV><p>
<hr size=1> <a href="http://us.lrd.yahoo.com/_ylc=X3oDMTFqODRtdXQ4BF9TAzMyOTc1MDIEX3MDOTY2ODgxNjkEcG9zAzEEc2VjA21haWwtZm9vdGVyBHNsawNmYw--/SIG=110oav78o/**http%3a//farechase.yahoo.com/">Yahoo! FareChase - Search multiple travel sites in one click.</a>