DIY Wideband Completed Pictures and Calibrating Resistor ?s

[efi_student]

It's the same style.  Not the exact connector.  If you look at the data
sheet it comes in many pin configurations.  The key is the inserts, the
rounded locking housing and the rubber internal seal.  I looked at every
connector Sumitomo listed on their site to determine which one looked to
be most like the one that I have seen both on the wiring harness and on
the sensors themselves.  This appears to be it from the description.  I
am 100% certain that the connector is Sumitomo, it's now just a question
of exactly which one it is.

Lance

-----Original Message-----
From: owner-diy_efi at diy-efi.org [mailto:owner-diy_efi at diy-efi.org] On
Behalf Of Steve.Flanagan at VerizonWireless.com
Sent: Thursday, December 13, 2001 7:19 AM
To: diy_efi at diy-efi.org
Subject: RE: DIY Wideband Completed Pictures and Calibrating Resistor ?s


That does not look like an 8 pin connector,

Anyway,  Why not just buy the sensor and once you have it in hand, try
to get the connector.



-----Original Message-----
From: efi_student [mailto:efi.student at sbcglobal.net]
Sent: Wednesday, December 12, 2001 3:04 AM
To: diy_efi at diy-efi.org
Subject: RE: DIY Wideband Completed Pictures and Calibrating Resistor ?s


http://www.sws.co.jp/stb_e/FRM/FILE/11FILE/sub11.htm

Does this look familiar to anyone?  I sent a request for contact to
Sumitomo USA, I will be enquiring about this connector to see if they
would be willing to sell a group buy lot.  Obviously, I don't have any
details just yet, but I will forward whatever they want to send me.

This connector is not limited to the Honda VX.  My Honda gurus tell me
that this connector is very common, and that there are at least two on
every OBDII Honda Civic engine loom, so it isn't necessary to chase down
the VX model.  Also, the '96-98 Civic HX uses a 5 wire sensor according
to my sources, but from a quick perusal of web resources, it appears
that Honda is even more proud of this piece than the one used in DIY. It
uses the same 8 pin connector and cal resistor scheme.

If anyone has an inside line with Sumitomo, it could be very useful
right now.

Lance

-----Original Message-----
From: owner-diy_efi at diy-efi.org [mailto:owner-diy_efi at diy-efi.org] On
Behalf Of Bruce
Sent: Tuesday, December 11, 2001 11:21 AM
To: diy_efi at diy-efi.org
Subject: Re: DIY Wideband Completed Pictures and Calibrating Resistor ?s



From: "Perry, Scott" <perry at sapphire.spdc.ti.com>
> But doesn't this require having the mating connector?  Unfortunately I
don't have time to go to junk yards looking for a Civic VX wiring
harness to mate to the O2 sensor connector.  Maybe you have other
suggestions...

Maybe someone with an extra would volunteer one. <hint, hint>.

Lacking that, there are blade ends, wire ties and RTV (sensor safe
obviously). Bruce


------------------------------------------------------------------------
----
To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
quotes) in the body of a message (not the subject) to
majordomo at lists.diy-efi.org

----- End of forwarded message from owner-diy_efi at diy-efi.org -----
------------------------------------------------------------------------
----
To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
quotes) in the body of a message (not the subject) to
majordomo at lists.diy-efi.org

----- End of forwarded message from owner-diy_efi at diy-efi.org -----
------------------------------------------------------------------------
----
To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
quotes) in the body of a message (not the subject) to
majordomo at lists.diy-efi.org

----- End of forwarded message from owner-diy_efi at diy-efi.org -----
----------------------------------------------------------------------------
To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org