intergrator and BLM

[Mike Rolica]

Done that, made ecu file for it too.  Every thing possible is in it for
calibrations.  Winbin is ok but in values it does not recognise stuff under
values.. elements that are more than 1 byte in size.  Ie for max knock
retard, is $fff5 or 3.5 deg.  It only see's FF even when element size is ecu
file is set to 2.  Works good in promedit.  Still have to check it out, has
over 135 options now :-)
Mike Rolica
EXT. 260
 :-)


	-----Original Message-----
	From:	Squash [SMTP:realsquash at yahoo.com]
	Sent:	Wednesday, November 03, 1999 1:57 PM
	To:	gmecm at efi332.eng.ohio-state.edu
	Subject:	RE: intergrator and BLM

	Code and tables are on the eprom that is on your
	memcal unit.  the tables start at 0 and the code
	starts at 3000H (in the eprom).  If you are serious
	about modifying your code, download the anht
	dissasembly from ecmguy.  all of the tables are in the
	exact same locations as your aujp(?).  There are also
	descriptions of most tables.

	Squash

	--- Mike Rolica <mrolica at meridian-mag.com> wrote:
	> Like I said to bruce, I don't like clutter.  Where
	> is the code stored on the
	> 730? Physically and address? -address? Is it like
	> the 165 and very similar
	> to the 68hc11f1 Motorola microcontroller?
	> Mike Rolica
	> EXT. 260
	>  :-)
	> 
	> 
	> 	-----Original Message-----
	> 	From:	David Cooley [SMTP:n5xmt at bellsouth.net]
	> 	Sent:	Wednesday, November 03, 1999 1:11 PM
	> 	To:	gmecm at efi332.eng.ohio-state.edu
	> 	Subject:	Re: intergrator and BLM
	> 
	> 	At 12:56 PM 11/3/1999 -0500, you wrote:
	> 	>OK, staying on this thread, How large is the BLM
	> on a 90 730 on a
	> f-body?
	> 	>Can it be enlarged from lets say 16 to 32 as to
	> give a finer
	> resolution?
	> 	>Does this make sense?, Also, can some of the fuel
	> map tables
	> PE/tables be
	> 	>enlarged to a finer resolution at cruise rpm, in
	> my instance
	> 1500-2600?  I
	> 	>know that the prom/memcal is pretty full but can
	> some of this stuff
	> be
	> 	>scraped because it is not used? Ie shift light
	> stuff, ccp, air
	> injection?
	> 	>Too free up space?
	> 
	> 
	> 	It could probably be done, but you just can't scrap
	> the tables...
	> The code 
	> 	will be looking for data in those locations.  You'd
	> need to totally 
	> 	re-write the code.
	> 	Why not just go to a newer PCM with more PROM space
	> and customize
	> from there?
	> 
	> 
	>
	===========================================================
	> 	David Cooley N5XMT Internet: N5XMT at bellsouth.net
	> 	Packet: N5XMT at KQ4LO.#INT.NC.USA.NA T.A.P.R. Member
	> #7068
	> 	We are Borg... Prepare to be assimilated!
	> 
	>
	===========================================================
	> 


	=====

	__________________________________________________
	Do You Yahoo!?
	Bid and sell for free at http://auctions.yahoo.com