intergrator and BLM

[Squash]

Tis true.  i've found a few differences between anht
and aujp.  The fan temps, octane compensation, and O2
come to mind.  But the locations are the same.  So far
0-500H is the same.  haven't gone further yet.

SquASH

--- CSH-HQ <nacelp at jvlnet.com> wrote:
> Careful, on some of the f-body/vette some of the
> tables are the same but 
> some of the switches are different (rad fan comes to
> mind).
> Grumpy
> 
> 
> Code and tables are on the eprom that is on your
> >memcal unit.  the tables start at 0 and the code
> >starts at 3000H (in the eprom).  If you are serious
> >about modifying your code, download the anht
> >dissasembly from ecmguy.  all of the tables are in
> the
> >exact same locations as your aujp(?).  There are
> also
> >descriptions of most tables.
> >
> >Squash
> >
> >--- Mike Rolica <mrolica at meridian-mag.com> wrote:
> >> Like I said to bruce, I don't like clutter. 
> Where
> >> is the code stored on the
> >> 730? Physically and address? -address? Is it like
> >> the 165 and very similar
> >> to the 68hc11f1 Motorola microcontroller?
> >> Mike Rolica
> >> EXT. 260
> >>  :-)
> >> 
> >> 
> >> 	-----Original Message-----
> >> 	From:	David Cooley [SMTP:n5xmt at bellsouth.net]
> >> 	Sent:	Wednesday, November 03, 1999 1:11 PM
> >> 	To:	gmecm at efi332.eng.ohio-state.edu
> >> 	Subject:	Re: intergrator and BLM
> >> 
> >> 	At 12:56 PM 11/3/1999 -0500, you wrote:
> >> 	>OK, staying on this thread, How large is the
> BLM
> >> on a 90 730 on a
> >> f-body?
> >> 	>Can it be enlarged from lets say 16 to 32 as to
> >> give a finer
> >> resolution?
> >> 	>Does this make sense?, Also, can some of the
> fuel
> >> map tables
> >> PE/tables be
> >> 	>enlarged to a finer resolution at cruise rpm,
> in
> >> my instance
> >> 1500-2600?  I
> >> 	>know that the prom/memcal is pretty full but
> can
> >> some of this stuff
> >> be
> >> 	>scraped because it is not used? Ie shift light
> >> stuff, ccp, air
> >> injection?
> >> 	>Too free up space?
> >> 
> >> 
> >> 	It could probably be done, but you just can't
> scrap
> >> the tables...
> >> The code 
> >> 	will be looking for data in those locations. 
> You'd
> >> need to totally 
> >> 	re-write the code.
> >> 	Why not just go to a newer PCM with more PROM
> space
> >> and customize
> >> from there?
> >> 
> >> 
> >>
>
>===========================================================
> >> 	David Cooley N5XMT Internet: N5XMT at bellsouth.net
> >> 	Packet: N5XMT at KQ4LO.#INT.NC.USA.NA T.A.P.R.
> Member
> >> #7068
> >> 	We are Borg... Prepare to be assimilated!
> >> 
> >>
>
>===========================================================
> >> 
> >
> >
> >=====
> >
> >__________________________________________________
> >Do You Yahoo!?
> >Bid and sell for free at http://auctions.yahoo.com
> >
> 
> 


=====

__________________________________________________
Do You Yahoo!?
Bid and sell for free at http://auctions.yahoo.com