[Gmecm] What does VSS do exactly?

Mon Jun 27 13:20:31 UTC 2005

Well, I removed the cruise, but yes, I think I had the first kind you
described (no CCC though).  The speedo cable goes into the gauge in the
dash.  The cruise looked like a vaccum thingy controlled by wires.  So, you
are saying that my speedo is already doing the job for me probably?  In
principle, I could trace the wires from the speedo to the buffer and get VSS
from there.  Is that right?  Any guess where they typically mount these
things?

Would the VSS signal go all the way out to the cruise stuff under the hood?
If so, since I removed the cruise, it would just be hanging open at a
connector and life would be incredibly easy... except for finding the
connection in the EFI harness.

Thanks for the help.

-----Original Message-----
From: gmecm-bounces at diy-efi.org [mailto:gmecm-bounces at diy-efi.org] On Behalf
Of Jay Vessels
Sent: Sunday, June 26, 2005 10:05 PM
To: gmecm at diy-efi.org
Subject: Re: [Gmecm] What does VSS do exactly?

Hi there!

A few questions:

1)  Do you have factory cruise control?  If it's the vacuum/electronic
system (i.e. there is a vacuum servo cabled to the throttle that has about 4
or 5 wires to it, as opposed to the vacuum/mechanical system that had the
speedo cable routed to a module under the hood) then you already have a VSS.
1983 was a weird year for that, since at least some vehicles got the
electronic version.

2)  Did it have the computer-controlled carburetor on it?  Some of the
California trucks did, and they would also have a VSS already.

If 1 or 2 is true, then the VSS is already there.  Find the VSS buffer
(small box, ribbon cable to the sensor, card-edge connector to the truck),
and the pin that's not 12V or ground is the VSS signal.  Hook it to the
ECM's VSS input pin and you're done.

Barring that, 3)  Do you have the stock speedometer?  If so, VSS is simple.
The factory speedometer has a rectangular hole in the back of it with a
small hole to one side.  The VSS phototransistor/LED pair fit that hole and
is attached with a single screw.  Any 1981-1989
(approximately) GM car with EFI or CCC will have a VSS in the back of the
speedometer (some FWD and later-80s cars exempted, just look for a
speedometer cable).  Grab it.  It will be a small black module attached to
the speedometer with a ribbon cable to a small box.  That box has a
card-edge connector with three pins.  Get the connector, too.  The connector
is ground, +12V, and the VSS output.  Connect the power supply to whatever's
handy, and run the VSS output to the ECM's VSS input pin.

Jay Vessels
1982 Chevrolet S-10 Sport, 2.8V6 TBI
1984 Chevrolet S-10 Blazer Sport, 2.8V6 carb. (for now)

Charles McDowell wrote:
> You're probably right.  Can you (or anyone else) point me in the right 
> direction for VSS stuff for an 83 K-5 Blazer with a 350?
> 
> I think the most pain will be that I bought a pre-made harness with no 
> VSS, so I'll have to dig into that to make the connections.
> 
> Thanks. 
> 
> -----Original Message-----
> From: gmecm-bounces at diy-efi.org [mailto:gmecm-bounces at diy-efi.org] On 
> Behalf Of Jay Vessels
> Sent: Sunday, June 26, 2005 3:34 PM
> To: gmecm at diy-efi.org
> Subject: Re: [Gmecm] What does VSS do exactly?
> 
> Hi there!
> 
> VSS does several things, and the newer the ECM the more things it's tied
to.
> The older 1227747 vintage ECMs do several things with VSS, most 
> notably parking the IAC at speed, and I believe stall saver (i.e. 
> sudden throttle close, such as letting off the throttle and pushing in 
> the clutch at speed when coming to a stop).
> 
> Newer ones such as the $A1 code in the '730 (1991-1994 3.1V6 MPI) use 
> VSS to determine much more, such as throttle follower (manual shift 
> assist), stall saver, idle speed adjustment, spark advance, etc. since 
> that code changes fuel and spark strategy based on whether the vehicle is
moving.
> 
> Considering how simple it is to hook up (stock parts abound as do 
> aftermarket ones) and the benefits in drivability (which is a big reason
>   to go EFI in the first place), why not connect it?
> 
> Jay Vessels
> 1982 Chevrolet S-10 Sport, 2.8V6 TBI
> 1984 Chevrolet S-10 Blazer Sport, 2.8V6 carb. (for now)
> 
> Charles McDowell wrote:
> 
>>Thanks for the reply.  I always thought the IAC "parked" itself when 
>>the car was shut off.  Do I understand correctly that I will probably 
>>not have a problem if my computer is the type that operates that way 
>>instead of recalibrating above a certain speed? Is there any good way 
>>to tell which I have?
>>
>>-----Original Message-----
>>From: gmecm-bounces at diy-efi.org [mailto:gmecm-bounces at diy-efi.org] On 
>>Behalf Of WopOnTour
>>Sent: Saturday, June 25, 2005 1:53 PM
>>To: gmecm at diy-efi.org
>>Subject: Re: [Gmecm] What does VSS do exactly?
>>
>>Charles
>>Depending on your box, VSS is used to trigger an IAC "reset" when a 
>>combination of TP and VSS are above predetermined limits. (typically 
>>high enough so the reset routine is not intrusive) At that time the 
>>ECM will usually command 255 "in" counts and then back the pintle out 
>>to a predetermined decel "ready" position (usually 60-140). It 
>>typically only does this once per IGN cycle. This is necc as the IAC 
>>doesn't really have any physical feedback circuit, so the ECM bases 
>>it's count strategy on this reset position. On newer PFI units this 
>>reset occurs ay IGN off instead. So not having a VSS may affect idle 
>>performance since the ECM can't know actual pintle position and can 
>>get quite a bit "out-of-sync" from the predicted position posted up in 
>>the data stream and displayed on a scan tool.
>>HTH
>>Regards
>>WopOnTour
>>
>>----- Original Message -----
>>From: "Charles McDowell" <charles at taildragger.info>
>>To: "'For discussion of GM EFI hardware and software'" 
>><gmecm at diy-efi.org>
>>Sent: Saturday, June 25, 2005 11:43 AM
>>Subject: [Gmecm] What does VSS do exactly?
>>
>>
>>
>>
>>>I converted my Blazer to TBI using a pre-made kit with no provision 
>>>for VSS.
>>>Everything seems fine, but I'm reading that I could have problems?  
>>>Can anyone say for sure what purpose the VSS serves?  I have all the 
>>>emissions stuff disabled, so I don't care about that.  I've read some 
>>>comments regarding IAC, but nobody can explain quite what that's all
> 
> about.
> 
>>>Thanks.
_______________________________________________
Gmecm mailing list
Gmecm at diy-efi.org
http://lists.diy-efi.org/mailman/listinfo/gmecm