[Gmecm] 88 Chevy S-10 Pickup -Fuel Injection Conversion on Jeep-

[Aphelion79]

Ah, I will look into that... thanks a bunch!  I'll dig into the wires 
sometime in the near future (its going to be pouring outside for the 
next few days it seems like) and let you know what I find!

-Matt

Jake Tucker wrote:

>Matt,
>	If you look at the GMECM FTP site, under /pub/manuals/1227747
>you'll find some scanned in wiring diagrams.  From the first pic
>(747ecm6.jpg), the EST bypass wire is shown connected to D5 of the 32
>pin connector.  On the 6th pic (747ecm6.jpg) that wire is shown going
>directly to the distributor on pin B.
>
>Jake
>
>-----Original Message-----
>From: gmecm-bounces at diy-efi.org [mailto:gmecm-bounces at diy-efi.org] On
>Behalf Of Aphelion79
>Sent: Friday, April 28, 2006 9:04 PM
>To: gmecm at diy-efi.org
>Subject: Re: [Gmecm] 88 Chevy S-10 Pickup -Fuel Injection Conversion on
>Jeep-
>
>Right what the dealerships etc. have been telling me, but I don't HAVE 
>an S-10. I just have the wiring and the ECM + TBI etc. from one. Does 
>anyone have any more specific info??  I may have cut off the connector 
>and need to know how it works with the ECM.  I'm guessing it comes out 
>of say, A1, and has the splice connector and then goes into something 
>like A2?   Does anyone know of any diagrams or info on where to look for
>
>a diagram etc?  I can get ECM numbers etc. later, if they're needed and 
>the year etc. isn't enough.
>
>Thanks for the continued support!
>-Matt
>
>Denny wrote:
>
>  
>
>>Early S-10's the disconnect is under the heater in the passenger side 
>>floor board.
>>----- Original Message ----- From: <GuitarCrazyJim at aol.com>
>>To: <gmecm at diy-efi.org>
>>Sent: Friday, April 28, 2006 6:16 PM
>>Subject: Re: [Gmecm] 88 Chevy S-10 Pickup -Fuel Injection Conversion 
>>on Jeep-
>>
>>
>>    
>>
>>>I'm not familiar with the S 10 but on 80s & early 90s Camaros the tan
>>>      
>>>
>
>  
>
>>>wire
>>>you are looking for is in the harness high on the firewall near the 
>>>passenger's
>>>side. You have to open the wire protection tubing to get to it.  On 
>>>Camaros
>>>the wire has a black connector to make disconnecting and reconnecting
>>>      
>>>
>
>  
>
>>>possible
>>>for setting the base timing.
>>>_______________________________________________
>>>Gmecm mailing list
>>>Gmecm at diy-efi.org
>>>http://lists.diy-efi.org/mailman/listinfo/gmecm 
>>>      
>>>
>>_______________________________________________
>>Gmecm mailing list
>>Gmecm at diy-efi.org
>>http://lists.diy-efi.org/mailman/listinfo/gmecm
>>
>>    
>>
>_______________________________________________
>Gmecm mailing list
>Gmecm at diy-efi.org
>http://lists.diy-efi.org/mailman/listinfo/gmecm
>
>_______________________________________________
>Gmecm mailing list
>Gmecm at diy-efi.org
>http://lists.diy-efi.org/mailman/listinfo/gmecm
>
>  
>