[Gmecm] Choosing ECM?

[Thomas Martin]

He comes off the transbrake now at 6000 rpm and shifts at 8000 rpm.  Alpha N
is really what he wants, he is planning at the moment, to keep his existing
distributor and MSD7 in there.

I was thinking if he idles at say 70 kPa and goes to 100 kPa, we could scale
the MAP with a voltage divider and give him idle at 30 kPa and then he has a
bit more granularity to run on the VE table.

What is Code 59?  Or is it who?

We are looking at low impedance 90 lb/hr injectors, so I will have to design
up a high to low impedance driver ckt.  That should be no worries there.

I told him it would be helpful to have a IAT and CTS sensor, but we could do
without and fix it them too, or put in dash switches for it so he can set
based on his weather station.  I like the IAT measuring the IAT as it will
show actual track temps of the air coming in.   And compensate for cold
start up.

Tom



On Fri, Sep 16, 2011 at 4:51 PM, Avery Nisbet <anisbet at gmail.com> wrote:

> Code 59 has fixed the max RPM limit already. I think its work up to or
> over 7k now.
>
> You could tune for just RPM.  Because the load will only change when
> you change tracks or if the weather changes at the track.
> Replace the Map sensor with a resistor and the TPS will be your only
> load scaling input.  There are a lot of EFI systems that work this
> way.
> Im sure the GM or mega$quirt stuff can be tricked into do this pretty
> easily.
>
> -Avery
>
> On Thu, Sep 15, 2011 at 6:12 AM, David Allen <davida1 at hiwaay.net> wrote:
> > Thomas, I would assume that cam does not have a smooth idle and does not
> > have much vacuum at idle. You may have your work cut out for you tuning
> that
> > thing!
> >
> > What level of horsepower and RPM is it running?  Different ECM's and
> > programs have limitations on the max RPM it can calculate. If you exceed
> > that RPM it won't output the data correctly and the tables may or may not
> be
> > scalable to that area.
> >
> > Not trying to discourage you from this project - just warning of a few
> > things you will have to overcome.  Others on the list can give more info
> on
> > specifics. I've never run into any RPM limits because my builds have used
> > turbos and not high RPM.
> >
> > Sincerely,
> > David
> >
> > ----- Original Message -----
> > From: Thomas Martin
> > To: gmecm at diy-efi.org
> > Sent: Wednesday, September 14, 2011 9:48 AM
> > Subject: [Gmecm] Choosing ECM?
> > Friend of mine is looking to run his 9.70 at 134-135 mph Olds Small Block
> > powered race car on EFI.  Cam is around 324 degrees at the seat.
> > For those who have run the OBD1 PCM/ECM's, what would be a good choice?
>  He
> > primarily needs it to handle fueling and timing.  Or would it really be
> > better to go with a LS1 PCM like an 0411 and OBD2?  Not worried about
> > flashing at the track to make changes.
> > It needs to idle, and goes WOT.  It spends very little time anywhere
> else.
> >  Currently has Nitrous (125 hp shot).
> > I have RT-CATS Tuner and TunerProRT, Moates APU1 (Burner/real time/RS232
> > interface/emulator combo) and he has a TPI computer now, he has to look
> and
> > see what PN hardware he has.  And he has a bunch of PROM's for it.
> > Thanks!
> > Tom
> >
> >
> > ________________________________
> >
> > _______________________________________________
> > Gmecm mailing list
> > Gmecm at diy-efi.org
> > http://lists.diy-efi.org/mailman/listinfo/gmecm
> >
> > _______________________________________________
> > Gmecm mailing list
> > Gmecm at diy-efi.org
> > http://lists.diy-efi.org/mailman/listinfo/gmecm
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.diy-efi.org/pipermail/gmecm/attachments/20110916/4f053f25/attachment.html