Wreckers, efi parts, which ones?

[Wes Branchflower]

Hmm.. it says $850 US.. which is about $1600 Australian. I forgot to mention 
i'm in Australia.
I think I need to use a MAF system, because i'll be using a hot cam.
But thanks anyway. I'll definetly keep them in mind.



>From: "P.J.Berg" <BergRace at c2i.net>
>Reply-To: diy_efi at diy-efi.org
>To: <diy_efi at diy-efi.org>
>Subject: Re: Wreckers, efi parts, which ones?
>Date: Sun, 21 Jan 2001 19:08:33 +0100
>
>Go to www.PerfectPower.com  (South Africa)
>The ECU is the cheapest, the MIC3 runs at 423,-U.S.$ including all sensors
>comunication cable at two-2 Ignition amplifiers.
>
>Tell them BergRace sendt you.
>
>
>
>
>P.J.Berg
>BergRace at Aircooled.net
>
>
>
>
>
>----- Original Message -----
>From: "Wes Branchflower" <hemi_265 at hotmail.com>
>To: <diy_efi at diy-efi.org>
>Sent: Sunday, January 21, 2001 6:03 PM
>Subject: Wreckers, efi parts, which ones?
>
>
> > I'm making a multiport EFi setup for my 265cu (4.3L) hemi six.
> > I've got the manifolds pretty much on their way, but, i'm just a little
> > stuck with the rest of it.
> >
> > Does anyone recommend a good EFi computer, which is easily programmed, 
>and
> > is available relatively cheap?
> >
> > Also, i'm weighing up between sensors, and i'll probablty be using a MAF
>as
> > i'll be using a fairly lumpy cam, which might upset a MAP sensor?
> >
> > I'm looking to source things from a wreckers, and wanting to keep on a
> > budget. I already have a Ford XF 4.1 litre throttle body/TPS +
> > injectors/fuel pressure regulator.
> >
> > Are the following all I need for my setup:
> >
> > MAF Meter
> > Throttle Position Sensor
> > Crank Angle sensor (or can i just do it from the coil?)
> > Coolant Temp Sensor
> > Fuel Pump
> > Fuel Pressure Regulator
> >
> >
> > MAF Meter - Do popular aftermarket ECU's accept both MAP or MAF sensors.
> >             Does it matter what 'size' a MAF is? Any suggestions for a
> > make which I should look for? (Ford? Holden? etc?)
> >
> > Throttle Pos Sensor - I have the one which came with the XF Ford 
>throttle
> > body, It doesn't seem to have any output except WOT and IDLE.
> > Either that or it's broken.. :( Is this all i need?
> >
> > Do I need a crank angle sensor for plain multi-port efi? (not 
>sequential)
> >
> > Do i need a coolant temp sensor? are their any makes/models that I can
>pull
> > one from at a wreckers if so? where are they located?
> >
> > Fuel Pump - Will a stock ford EFi pump do? I'm using the ford injectors
>and
> > pressure regulator.
> >
> > Any input greatly appriecated.
> > Thanks.
> >
> >
> >
> >
> >
> >
> > 
>_________________________________________________________________________
> > Get Your Private, Free E-mail from MSN Hotmail at 
>http://www.hotmail.com.
> >
> > 
>--------------------------------------------------------------------------
>--
> > To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
>quotes)
> > in the body of a message (not the subject) to 
>majordomo at lists.diy-efi.org
> >
>
>
>----------------------------------------------------------------------------
>To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the 
>quotes)
>in the body of a message (not the subject) to majordomo at lists.diy-efi.org
>

_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.

----------------------------------------------------------------------------
To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org