[Diy_efi] Re: oopic2 based controller

Kent Martin kentmartin at froggy.com.au
Mon Aug 26 03:16:52 GMT 2002


I'm already using a MC16c/62 and they are quite good for this application 
with only a few draw backs.

Kent.
----- Original Message ----- 
From: "Dan Zorde" <dzorde at erggroup.com>
To: <diy_efi at diy-efi.org>
Sent: Thursday, August 22, 2002 10:07 AM
Subject: [Diy_efi] Re: oopic2 based controller



May I suggest that you look at the Mitsubishi M16C/62 family controllers
(around US$8/ea for 64K Flash version), you can replace a 64K version
with a 128K or 256K Flash version direct replacement if you need more
memory.

Just as an example they have:
? Memory capacity...................................ROM (See Figure
1.1.4.ROM Expansion)
RAM 10K to 20K bytes
? Shortest instruction execution time .......62.5ns
(f(XIN)=16MHZ,VCC=3.0V to 3.6V)
142.9ns (f(XIN)=7MHZ,VCC=2.4V to 3.6V without software wait)
? Supply voltage ......................................3.0V to 3.6V
(f(XIN)=16MHZ,without software wait)
2.4V to 3.0V (f(XIN)=7MHZ,without software wait)
2.2V to 3.0V (f(XIN)=7MHZ,with software one-wait):mask ROM version
? Low power consumption .......................34.0mW (VCC
=3V,f(XIN)=10MHZ,without software wait)
66.0mW (VCC =3.3V,f(XIN)=16MHZ,without software wait)
? Interrupts ...............................................25 internal
and 8 external interrupt sources,4 software
interrupt sources;7 levels (including key input interrupt)
? Multifunction 16--bit timer ......................5 output timers +6
input timers
? Serial I//O ..............................................5 channels
(3 for UART or clock synchronous,2 for clock synchro-
nous)
? DMAC ...................................................2 channels
(trigger:24 sources)
? A--D converter.......................................10 bits X 8
channels (Expandable up to 18 channels)
? D--A converter.......................................8 bits X 2
channels
? CRC calculation circuit ..........................1 circuit
? Watchdog timer.....................................1 line
? Programmable I//O ...............................87 lines
? Input port ...............................................
_______
1 line (P85 shared with NMI pin)
? Memory expansion ...............................Available (to 4M
bytes)
? Chip select output .................................4 lines
? Clock generating circuit ........................2 built-in clock
generation circuits
(built-in feedback resistor,and external ceramic or quartz oscillator)

They also have a range of actual automotive processors such as M32160
(-40 to 110degC), featuring stacks of timers and serial i/o.

cheers

Dan  dzorde at erggroup.com


From: "Bino Lardo" <binolardo at hotmail.com>
>
>do you have another idea of a microcontroller for cheap? and for the
fuel
>spark table it could be smaller.


---------------------------- ERG Group --------------------------
 The contents of this email and any attachments are confidential
 and may only be read by the intended recipient.
-----------------------------------------------------------------


_______________________________________________
Diy_efi mailing list
Diy_efi at diy-efi.org
http://www.diy-efi.org/mailman/listinfo/diy_efi





_______________________________________________
Diy_efi mailing list
Diy_efi at diy-efi.org
http://www.diy-efi.org/mailman/listinfo/diy_efi



More information about the Diy_efi mailing list