[Diy_efi] WBO2 Project

Wed Jun 19 03:49:45 GMT 2002

This is a multi-part message in MIME format.

--Boundary_(ID_U1K1oGmbCcs6FC20rFWEFA)
Content-type: text/plain; charset=US-ASCII
Content-transfer-encoding: 7BIT

Hi, I'm not sure if anyone can answer this or not, or if I am using the
right resourses (this address). But I have completed the WBO2 project
and went through all the check point listed; everything checks out as
far as voltages go. The only problem I am having is when the voltages
are supposed to change range. for ex :

Keeping the DVM on U2 pin 8 close the switch. The voltage will slowly
drop. It will take ~ 2 minutes with the voltage reaching ~ -3.4 v. 
*	If not check C10, R18, R34 and U2. 

For some reason it takes mine well over 2 minutes to change.. more like
10-15 minutes.. and the same goes for the following:
Upon closing the switch the voltage at J8 will drop. After a pause the
voltage will slowly increase. It will take approximately 1 minute & 15
seconds for the voltage to reach maximum. 

Any help you have or ideas which can lead me into the correct direction
will be greatful

Thanks,

Lou Fourquet

--Boundary_(ID_U1K1oGmbCcs6FC20rFWEFA)
Content-type: text/html; charset=US-ASCII
Content-transfer-encoding: 7BIT

<html xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns="http://www.w3.org/TR/REC-html40">

<head>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=us-ascii">

<meta name=ProgId content=Word.Document>
<meta name=Generator content="Microsoft Word 10">
<meta name=Originator content="Microsoft Word 10">
<link rel=File-List href="cid:filelist.xml at 01C2165C.A524F460">
<!--[if gte mso 9]><xml>
 <o:OfficeDocumentSettings>
  <o:DoNotRelyOnCSS/>
 </o:OfficeDocumentSettings>
</xml><![endif]--><!--[if gte mso 9]><xml>
 <w:WordDocument>
  <w:SpellingState>Clean</w:SpellingState>
  <w:GrammarState>Clean</w:GrammarState>
  <w:DocumentKind>DocumentEmail</w:DocumentKind>
  <w:EnvelopeVis/>
  <w:Compatibility>
   <w:BreakWrappedTables/>
   <w:SnapToGridInCell/>
   <w:WrapTextWithPunct/>
   <w:UseAsianBreakRules/>
   <w:UseFELayout/>
  </w:Compatibility>
  <w:BrowserLevel>MicrosoftInternetExplorer4</w:BrowserLevel>
 </w:WordDocument>
</xml><![endif]-->
<style>
<!--
 /* Font Definitions */
 @font-face
	{font-family:SimSun;
	panose-1:2 1 6 0 3 1 1 1 1 1;
	mso-font-alt:\5B8B\4F53;
	mso-font-charset:134;
	mso-generic-font-family:auto;
	mso-font-pitch:variable;
	mso-font-signature:3 135135232 16 0 262145 0;}
@font-face
	{font-family:"\@SimSun";
	panose-1:2 1 6 0 3 1 1 1 1 1;
	mso-font-charset:134;
	mso-generic-font-family:auto;
	mso-font-pitch:variable;
	mso-font-signature:3 135135232 16 0 262145 0;}
 /* Style Definitions */
 p.MsoNormal, li.MsoNormal, div.MsoNormal
	{mso-style-parent:"";
	margin:0in;
	margin-bottom:.0001pt;
	mso-pagination:widow-orphan;
	font-size:12.0pt;
	font-family:"Times New Roman";
	mso-fareast-font-family:SimSun;}
a:link, span.MsoHyperlink
	{color:blue;
	text-decoration:underline;
	text-underline:single;}
a:visited, span.MsoHyperlinkFollowed
	{color:purple;
	text-decoration:underline;
	text-underline:single;}
span.EmailStyle17
	{mso-style-type:personal-compose;
	mso-style-noshow:yes;
	mso-ansi-font-size:10.0pt;
	mso-bidi-font-size:10.0pt;
	font-family:Arial;
	mso-ascii-font-family:Arial;
	mso-hansi-font-family:Arial;
	mso-bidi-font-family:Arial;
	color:windowtext;}
span.SpellE
	{mso-style-name:"";
	mso-spl-e:yes;}
span.GramE
	{mso-style-name:"";
	mso-gram-e:yes;}
@page Section1
	{size:8.5in 11.0in;
	margin:1.0in 1.25in 1.0in 1.25in;
	mso-header-margin:.5in;
	mso-footer-margin:.5in;
	mso-paper-source:0;}
div.Section1
	{page:Section1;}
 /* List Definitions */
 @list l0
	{mso-list-id:85343742;
	mso-list-template-ids:2100362472;}
@list l0:level2
	{mso-level-number-format:bullet;
	mso-level-text:o;
	mso-level-tab-stop:1.0in;
	mso-level-number-position:left;
	text-indent:-.25in;
	mso-ansi-font-size:10.0pt;
	font-family:"Courier New";
	mso-bidi-font-family:"Times New Roman";}
ol
	{margin-bottom:0in;}
ul
	{margin-bottom:0in;}
-->
</style>
<!--[if gte mso 10]>
<style>
 /* Style Definitions */ 
 table.MsoNormalTable
	{mso-style-name:"Table Normal";
	mso-tstyle-rowband-size:0;
	mso-tstyle-colband-size:0;
	mso-style-noshow:yes;
	mso-style-parent:"";
	mso-padding-alt:0in 5.4pt 0in 5.4pt;
	mso-para-margin:0in;
	mso-para-margin-bottom:.0001pt;
	mso-pagination:widow-orphan;
	font-size:10.0pt;
	font-family:"Times New Roman";}
</style>
<![endif]-->
</head>

<body lang=EN-US link=blue vlink=purple style='tab-interval:.5in'>

<div class=Section1>

Hi, I&#8217;m
not sure if anyone can answer this or not, or if I am using the right resourses (this address). But I have completed the WBO2
project and went through all the check point listed; everything checks out as
far as voltages go. The only problem I am having is when the voltages are
supposed to change range&#8230; for ex :<o:p></o:p>

<p class=MsoNormal style='mso-margin-top-alt:auto;mso-margin-bottom-alt:auto;
margin-left:.25in'><font size=3 face="Times New Roman"><span style='font-size:
12.0pt'><o:p>&nbsp;</o:p></span></font></p>

Keeping the
DVM on U2 pin 8 close the switch. The voltage will slowly drop. It will take ~ 2 minutes with
the voltage reaching ~ -3.4 v. <o:p></o:p>

<ol start=1 type=1>
 <ul type=circle>
  <li class=MsoNormal style='color:blue;mso-margin-top-alt:auto;mso-margin-bottom-alt:
      auto;mso-list:l0 level2 lfo1;tab-stops:list 1.0in'><font size=3
      color=blue face="Times New Roman"><span style='font-size:12.0pt'>If not
      check C10, R18, R34 and U2. <o:p></o:p></span></font></li>
 </ul>
</ol>

<p class=MsoNormal style='mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><font
size=3 face="Times New Roman"><span style='font-size:12.0pt'><o:p>&nbsp;</o:p></span></font></p>

<p class=MsoNormal style='mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><font
size=3 face="Times New Roman"><span style='font-size:12.0pt'><o:p>&nbsp;</o:p></span></font></p>

For some reason it
takes mine well over 2 minutes to change.. more like 10-15 minutes.. and the
same goes for the following:<o:p></o:p>

Upon closing
the switch the voltage at J8 will drop. After a pause the voltage will slowly
increase. It will take approximately 1 minute &amp; 15 seconds for the voltage
to reach maximum.&nbsp;<o:p></o:p>

<p class=MsoNormal style='mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><font
size=3 face="Times New Roman"><span style='font-size:12.0pt'><o:p>&nbsp;</o:p></span></font></p>

<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Any help you have or ideas which can lead me into the
correct direction will be <span class=SpellE>greatful</span><o:p></o:p></span></font></p>

<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p>&nbsp;</o:p></span></font></p>

<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Thanks,<o:p></o:p></span></font></p>

<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p>&nbsp;</o:p></span></font></p>

<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Lou <span class=SpellE>Fourquet</span><o:p></o:p></span></font></p>

</div>

</body>

</html>

--Boundary_(ID_U1K1oGmbCcs6FC20rFWEFA)--

_______________________________________________
Diy_efi mailing list
Diy_efi at diy-efi.org
http://www.diy-efi.org/mailman/listinfo/diy_efi