TPI fuel pressure

[Dan Townsend]

Well I have the gauge from hypertech and it gets twitchy above a certain
spot.  Not sure if it was the gauge or the pump not keeping up at those
levels.  The new pump can perform at higher than stock levels so I'll test
the gauge with it as soon as my friend gives it back.  He has only had it
for a year :-)

DanT

----- Original Message -----
From: "Marteney, Steven J." <smarteney at xlvision.com>
To: <gmecm at diy-efi.org>
Sent: Monday, February 26, 2001 2:32 PM
Subject: RE: TPI fuel pressure


> Gauge was VERY steady on the 305 IROC, very erratic on my car.  Same
gauge.
> So unless the gauage behavior varies from connection to connection, I
doubt
> it's the gauge.  Clearly more testing is needed.  Been wanting to do the
> in-car test with gauge on windshield but my hose is short enough really
only
> the passenger can see.  Will do that tomorrow on the way to work.  My
> carpool partner needs something to do!
>
> The inline filter really is new!  Replaced it not that long ago.  Can't
> imagine it being the cause.
>
> Steve (lookin for a few good little guys!)
>
> -----Original Message-----
> From: Dan Townsend [mailto:xybertron at cox-internet.com]
> Sent: Monday, February 26, 2001 2:41 PM
> To: gmecm at diy-efi.org
> Subject: Re: TPI fuel pressure
>
>
> There is a filter on the pump but it is probably ok.  I just swapped my
fuel
> pump and mine was 14 years old and just rather dirty.  The problem is
> probably the inline filter which you unscrew not cut :-)  They can cause
> problems like what your having.  The erratic needle movements is somtimes
> the gauge.  I think someone mentioned using a isolator before.  Pressure
> (for 350) should be around 40 with vacuum and about 8 psi more with no
> vacuum.  If you have ever looked at a MAP log you would see blipping the
> throttle cause the vacuum to change but then go back to almost what it was
> at idle thus confusing your readings.  Take the gauge and tape it to the
> window.  Check pressure then unhook vacuum.  Should go up then hook up
> vacuum and go for a WOT run.  Pressure show go to same as with unhooked
> vacuum at idle.  If not check the filter and then pump.
>
> Hope that helps,
> DanT
>
> ----- Original Message -----
> From: "Marteney, Steven J." <smarteney at xlvision.com>
> To: <gmecm at diy-efi.org>
> Sent: Monday, February 26, 2001 11:19 AM
> Subject: RE: TPI fuel pressure
>
>
> > Line filter was replaced several months ago.  There's a filter in the
> > tank???
> >
> > Steve
> >
> > -----Original Message-----
> > From: slowfatslug [mailto:slowfatslug at hotmail.com]
> > Sent: Monday, February 26, 2001 10:37 AM
> > To: gmecm at diy-efi.org
> > Subject: Re: TPI fuel pressure
> >
> >
> >   I crack the throttle and it
> > > initially goes up, then settles at a LOWER pressure than at idle.  If
I
> > > unhook the vacuum, it is still erratic.
> > >
> > Could be a clogged filter in the tank... If  line filter hassent been
> > replaced lately Id cut it open and see whats in there..
> >
> > dan
>
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo at lists.diy-efi.org
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo at lists.diy-efi.org
>

----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo at lists.diy-efi.org